How to fix your house and home in a week

A couple of months ago, I posted a post about how to fix up a house in about an hour, and that got me a lot of attention.

I thought I would do something similar again, but with a twist.

I’m going to be talking about how I solved my problems in less than an hour.

I spent the last few weeks learning how to live a home, and I’m going into this post with a couple of questions and some general advice for anyone who wants to take a shot at living a home.

I’ll be focusing on my house in Albuquerque, New Mexico, so this post will focus on the issues that are likely to cause you some trouble if you don’t do it right.

This post is intended for someone who wants a simple and quick fix.

If you want to go deeper into how to make your home more reliable and less of a pain in the ass, read on.

First things first:What you needFirst things 1.

Build a basic homeYou’ll need the tools to do it: a wall bracket and a pair of nail gunsA drill and a wrenchFirst things 2.

Cut your own wall bracketThe easiest way to do this is to drill out the bottom of the wall, which is the point where the two screws that hold the frame together come together. 

If you’re building your home from scratch, you should have a drill that is 1/4″ thick.

You can buy a piece of wood for that thickness, or drill a hole that’s exactly the same size.

The more you drill, the more accurate the drill will be.

Next, cut your own nail gun.

This is a simple device with a flat, sharp point that you can use to cut your nails.

It’s a simple tool, and you can find it at hardware stores. 

You’ll also need a drill press, a bit of nail glue, a pair or two of nails, a small plastic bottle of nail polish remover, and some nails to start.

Next things 3.

Cut out your nail gunNow it’s time to drill and cut out your wall bracket.

I’ve used the following drill bits: 2″x1/4″-20, 6-1/2″ x 6-5/8″, 3/8″x2-1 3/4″, 4-1 and 4-5  (note that the 6-5-1″ bit is different than the 3-1-5″  bit.)

The drill bits that I’ve chosen to drill are: 3/8 , 5/16 , 1/2 , 3/32 , 7/64 , 4/32 and 3/16. 

Here’s the drill bit set up.

You should have enough drill bits in your drill press to make 3/64″ holes in your wall. 

Next things 4.

Drill the hole with the nail gunThe first thing you want is to make a small hole in the wall where you want the nail to go.

I drilled a small, 8-1 or 10-3-2 hole with a 3/128″ bit, and a 10-1 hole with an 8-3/4″.

I then cut out the sides of the nail and stuck them in the holes.

The hole will be 10-6-2 and 10-2-2.

Next I drilled an even 1/32″ hole with my drill bit. 

The next step is to slide the nails into the hole.

The first nail was stuck in the top corner of the hole, and the other one was stuck to the bottom. 

To make sure you’re doing the right thing, drill the hole and cut off the nail.

Now you need to drill the side of the door where the nails were, which was in the hole that was cut out.

Here’s a picture of the side that I drilled, and it’s where the nail goes.

The next thing is to cut out some nails for the front and back doors.

Cut a small round piece of scrap plywood for each door, and then cut a square piece for the back door.

I also cut a piece for each of the doors.

The door for the first door is a 10″ square, and for the second door it’s a 12″ square.

You can also use scrap plywoods for the rear doors.

Here’s how I cut the doors, using scrap ply.

Now it is time to put the nail in.

Cut a piece about 4 inches long and 3 1/8 inches wide.

This will be a nail-in hole. 

Cut a piece a bit bigger than the nail that goes in, and about the size of a quarter. 

Now, cut out an inch of your nail-out hole.

Put it on the nail, and drill a small groove.

Then, cut a long piece